Home > Windows 98 > Windows 98 CD Drive Problem

Windows 98 CD Drive Problem

Contents

The biggest problem is doing this is often locating your CD-ROM drive's real mode driver in the first place. If the hard disk is badly fragmented, it may be impossible to install any programs.i. Verify that if its an IDE drive, its installed according to step 6 of http://support.microsoft.com/kb/126380/en-usf. The place to look is the config.sys file in the root folder of your C: drive. http://yellowproductions.net/windows-98/win98-no-cd-drive.php

To do so, you need to find out precisely what model of CD-ROM drive it is that you have. I was just getting angry, and like you said, ski, stepping away for a while really helped out. Bad CD-ROM drive If all the above steps have been tried and you're still encountering errors with reading discs in the CD-ROM drive, it's possible that the drive is bad. The portion of the Config.sys file that you're interested in are the lines marked as [CD], where the set of generic CD-ROM drivers are referenced.

Windows 98 Cd Rom Driver

As far as device status, it is showing: The device is either not present, not working properly, or does not have all of the drivers installed. Do same 4 "Upper filters"..........close window and restart computer.............without touching any buttons on keyboard....except to login......you should see driver being installed once again for your dvd/cd drive.........GOOD LUCK!!!!!!!!!!!!!!!!!!! Edit the file to add the command lh c:\dos\mscdex.exe /s /d /idecd001d.

  1. If the first one does not work, continue with the next.
  2. How do I go about acquiring the proper driver and how do I install it on my machine so my computer can recognize the Win98 setup files?
  3. Under Performance by File System, verify it says '32-bit'.
  4. Is this what is causing the problem?
  5. If it's a desktop, are both the HDD & CD drive connected to the same IDE cable?
  6. With the advent of MP3 players and ITunes, the music industry also joined in to capitalize on the media frenzy.
  7. cd/dvd working just fine now.
  8. My external disk drive works on my laptop(windows 7)But it won't recognize any cd-rs and that's what I bought it for.All other i got a Toshiba laptop windows 8 and my
  9. Once recovered, I installed Norton 360 ver 3.0 along with MS Office 2007.

All Rights ReservedAd Choices The information on Computing.Net is the opinions of its users. Report • #10 riider March 16, 2012 at 08:28:49 "putting in the W 98 it will load to a certain point then fail"Can you explain in more detail? "8. if this is your case as well use knoppix (which does rule), boot the computer into knoppix and drop the drivers into your hard drive reboot into windows and place the Windows 98 Download The optical drive will then be seen and you can copy the files using dos commands.

If you have jumpered it correctly on the second system, then it should work. Windows 98 Not Recognizing Cd Drive Please refer to our CNET Forums policies for details. I have over … [Read More...]Technology Rapidly Changing The Face of Home CareTechnology and medical advances are allowing people to live longer and healthier lives.  From this industry a new frontier All rights reserved.

Report • #2 ToshibaPortegeM400 March 15, 2012 at 15:31:01 Hi ,It is as namesake a Toshiba Portege M400 Laptop with a Windows XP system originally on it (no longer present or Kjeld, Denmark. Additional information See our CD-ROM, DVD, and Blu-Ray definitions for further information and related links on these terms. The important thing here is to ensure that the Autoexec.bat file references this by the same name as the Config.sys file.

Windows 98 Not Recognizing Cd Drive

Almost 5 years ago... Before you do [if you wish] you could run "Step-by-step Confirmation" and hit "Enter" at every command to see if any errors result. Windows 98 Cd Rom Driver Regarding: "I do, however, have yellow exclamation points in 3 places. Windows 98 Dvd Drivers Click Start->Run and type regedit to edit the registry.

You'll need to do your own homework for that. click site Computing.Net and Compnet Ventures, LLC hereby disclaim all responsibility and liability for the content of Computing.Net and its accuracy. Ask a question Member requests are more likely to be responded to. If it is an 80pin cable and the only drive you usually need it jumpered as CS and put on the end of the cable. How To Install Windows 98

SHOW ME NOW CNET © CBS Interactive Inc.  /  All Rights Reserved. They are: Under PCI Bus, subheading SiS 5513 Dual PCI IDE controller, there are two items with yellow exclamations: 1) Primary IDE Controller (dual fifo) 2) Secondary IDE Controller (dual fifo) Try it! news Check your computer ( this problem is mainly seen on XP computers ) for the application Roxio Easy CD Creatorb.

Advertisements do not imply our endorsement of that product or service. Install the latest Windows Vista RCI from http://support.microsoft.com/kb/924924/h. Then they gave me numbers to call microsoft because since their program was removed and the problem still existed it was not a problem with norton.

Thanks again for your help, Ski.

Thanks again Report turnkey- Jan 24, 2010 at 11:28 AM THANK YOU! No biggie, since I just ordered an actual Win 98 disk from eBay (with license). Report DKTMB- Mar 9, 2010 at 03:43 AM Those THANK YOU's are from the three lost drives that were found. Verify computer running in 32-bit mode Windows 95 and Windows 98 users only Verify that your computer is running in 32-bit mode by clicking Start, Settings, Control Panel, double-click System, and

Thanks, Michael S. Problem: Cannot read information on a CD or DVD.a. I know you're not supposed to do this, but in an ironic twist of events my old computer got zapped pretty bad before I had a chance to back up the More about the author Exit Registry Editori.

I assume you also did "Save & Exit Setup" to save the changes. Verify that the SCSI drive is installed according to Step 5 of http://support.microsoft.com/kb/126380/en-use. You may have to enter the administrator password if requestedc. without driver support ?Linux would be easier Mint is good !Googling is quicker than waiting for an answer....

Using a text editor such as Wordpad, add a line that references the gscdrom.sys file. Removed Adaware that was on the computer but not used since 11/2009 - drives still not functioning. I've tried to pick option 1 and 2 and both times it tries to search for the CD driver "OEMCD001." Each time it doesn't find the driver, it aborts the installation, If it does not work there, then it's probably toast.

Update the DVD driver with the latest version of software from the manufacturer's website.ix. WinXP won't recognize a SATA drive. If listed with a yellow exclamation mark or red X, remove the CD-ROM by highlighting the drive and pressing the delete key.