These entries are located at the end of the file and may provide clues as to the cause of the problem. During shutdown, Win98 does not stop this program, causing the system to generate the error message. To begin with, you will lose any work you have not yet saved to the hard drive. Remove the check mark from in front of "Load startup group items." Restart Windows. http://yellowproductions.net/windows-98/win98se-cd-rom-help.php
Check out section 3w for tips on improving system performance and section 9w for tips from selected Websites. Click the Settings tab, click Advanced, click the Adapter tab, and then click Change. There are several other shutdown problems, but this seems to be the major one.”It could be a sound problemJanVossen had this suggestion: “Launch the System Configuration Utility (shown in Figure A) If you have Windows Millennium (ME) the procedure is a little different. https://support.microsoft.com/en-us/help/238096/problems-shutting-down-windows-98-second-edition
NOTE: Microsoft has also learned that some customers have been replacing the Windows 98 Second Edition version of the Configmg.vxd file with the Windows 98 version to address shutdown issues. Click the IRQ steering tab. End everything but Explorer, which is Windows itself. You should not have to read all of this document.
Click OK, and then click Yes to restart the computer. Under Settings, click to clear the following check boxes: (1) Disable System ROM Breakpoint; (2) Disable Virtual HD IRQ; (3) EMM Exclude A000-FFFF. This is an untested scenario that could result in blue-screen error messages, CPI errors, and hardware failures. Shut down Windows (observe whether it shuts down normally).
Click [Start]| Run. Windows 98 Shutdown Command Search the Dell Knowledge Base Documents for keywords such as shutdown, lockup, freeze, slow, etc. When the shutdown problem occurs, you will have identified the command causing the problem. http://www.infocellar.com/software/shutdown-problems-win98se.htm Test Windows shutdown.
A damaged Exit Windows sound file. PLEASE NOTE: You should not attempt scandisk or defrag until you have made at least a third of your hard drive partition space available by deleting files and moving applications. Many error messages occur not only at shutdown, but at startup or during use of the computer, so it is all but impossible to catalogue them separately just for shutdown troubleshooting Choose Command Prompt Only.
Press N for all other prompts. (You will cycle through the additional lines, selecting a *different* additional command each time until you have gone through them all.) Each time, after Windows https://www.cnet.com/forums/discussions/win98se-freezes-at-shutdown-screen-59137/ If your computer shuts down correctly, one of your startup programs is probably causing this issue. Windows 98 Second Edition Shutdown Supplement After your computer restarts, test Windows shutdown. Check which programs are used/loaded on startup/shutdown.
Physically remove the network card. have a peek at these guys Any suggestions? Check which programs are used/loaded on startup/shutdown. Once you have determined which line is causing your problem you can leave it unchecked as long as it doesn't cause other problems.
To configure Windows to not use the PnP BIOS, follow these steps: Reboot your machine and hold the CTRL key until you see the Windows 98 Start menu. This is controlled in Display properties on the Web tab. IMPORTANT WIN95 NOTE: Holding down the SHIFT key as soon as Windows begins to load will launch Win95 in Safe Mode. (If you wait for the desktop wallpaper to appear, it check over here To troubleshoot Windows using MSCONFIG: 1.
Contact your computer's manufacturer for assistance. On the Resources tab, verify that there are no conflicts listed under Conflicting Device List. Programs running in the background can cause many Windows problems including slowness. ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ Windows 98 and Millennium (ME) automatically load programs when you boot your computer.
If you’d like to submit a topic for our weekly pop quiz, please drop us a note. After you restart, attempt to shut down Windows. If shutdown is now successful, it is most likely an indication the system BIOS is contributing to the shutdown problems. Under the Win.ini tab, check the Sounds configuration and select an existing sound for shutdown or make sure no sound will be played.”Greg A. Flag Permalink This was helpful (0) Collapse - It could be hanging on by TONI H / January 22, 2005 1:04 AM PST In reply to: Win98SE freezes at shutdown screen
This update detects whether the appropriate version of the Configmg.vxd file is installed, and replaces any earlier versions with the Windows 98 Second Edition version. Restore the file from your Windows disk or wherever you obtained it and then test Windows shut down. Detailed instructions for troubleshooting these items are not given in the present article; if you do not know how to test these steps, please seek help in the online peer support this content Click the Performance tab.
If the system hangs, restore your CONFIG.SYS file to its original configuration. Windows seems to have recurring problems with it. You may need to install updated drivers for these devices. Please note that you use this information only at your own risk -- I am not personally able to verify, in advance, the consequences of any action on every computer of
Download and install the Windows 98 Second Edition Shutdown Supplement at this URL: http://www.microsoft.com/windows98/downloads/contents/WURecommended/S_WUFeatured/Win98SE/Default.asp You can also access this information from the Microsoft Knowledge Base at http://www.microsoft.com/ms.htm Go to the Search They are listed in order of most to least-common cause of shutdown problems.(Return to TOC) 3t. If the box is missing in Windows 98 SE, it means you have already applied the Shutdown Patch, which has permanently disabled Fast Shutdown and then removed the box.